DAIICHISEIKO Handrail Mounting Adaptor

This option allows the installation of tools, such as the Uketaro, Chibi Lark, and Multi Stand 130, on the handrails of the boat.

[Supported Models]
• Chibi Lark/Chibi Lark Type S
• Multi Stand 130
• Free Stand/Free Stand 130
• Uketaro/Uketaro 130
• Super Uketaro/Super Uketaro 130
• Ukejiro/Ukejiro 130
• Super Ukejiro/Super Ukejiro 130
• Ryoujiku Ukejiro/Ryoujiku Uketaro 130

SPEC : 

● Size:
Fixed side adapter: 40 mm × 60 mm × 21 mm
Adapter on washer side: 40 mm × 56 mm × 34 mm
● Weight: 78 g (with large O-ring installed)
● Materials: Glass fiber reinforced plastic (body)/Ethylene propylene diene monomer (EPDM) (O-ring)
● Accessories: Adapter (fixed side and washer side) × one each, O-ring (a large one with an inner dia. of approx. 56 mm and a small one with an inner dia. of approx. 42 mm) × one each, and silicone band × two (one for a spare)
MADE IN JAPAN

Usage example

Usage example

Mountable pipe diameter

[20 - 35 mm dia.]
Chibi Lark/Chibi Lark Type S

[20 - 40 mm dia.]
Multi Stand 130/Free Stand (130)
Uketaro (130)/Super Uketaro (130)
Ukejiro (130)/Super Ukejiro (130)
Ryoujiku Uketaro (130)[How to use] 1. Select the O-ring.

[How to use] 1. Select the O-ring.

[Large O-ring]
Chibi Lark/Chibi Lark Type S/Multi Stand 130
Uketaro 130/Super Uketaro 130/Super Ukejiro 130/Super Ukejiro 130/Ryoujiku Uketaro 130

[Small O-ring]
Free Stand/Free Stand 130 Uketaro/Super Uketaro/Ukejiro/Super Ukejiro/Ryoujiku Uketaro

[How to use] 2. Attach the O-ring to the adapter on the fixed side.

Use a silicone band to attach the O-ring to the fixed side adapter.

(1) Thread the silicone band through the O-ring.
(2) Hook the O-ring onto the adapter and slide the silicone band all the way inside.
(3) Turn the O-ring over while holding the silicone band with your fingers. If the silicone band looks like the enlarged figure (A), turn the O-ring over again.

[How to use] 3. Attach the fixed side adapter to the clamp.

Attach the fixed side adapter to the clamp by turning the installed O-ring around and hooking the O-ring.

[How to use] 4. Attach the washer-side adapter to the clamp.

Unbuckle the buckle from the washer-side adapter and attach the adapter clamping to the washer.

[How to use] 5. Attach the rod keeper.

Tighten and secure the clamp screws while aligning the washer-side adapter with the boat’s side pipe structure, such as a handrail.

Make sure that the product is rigidly fixed in place before use.

* Both adapters are symmetrical in design, and there are no restrictions on orientation.

Caution!

● When removing the adapters from the pipe, hold the fixed side adapter by hand.
Failure to do so may cause the adapter to fall into the sea.
● The adapter may rotate on the pipe if a strong force is applied.
● For a clamp that can be mounted vertically or horizontally, mount the clamp horizontally.
● Do not tighten the screws excessively. No matter how much you tighten the screws beyond a certain point, there will be no change in the fixation force.
● The non-slip rubber will deteriorate under ultraviolet light. Therefore, do not store it outdoors.
● The O-ring and silicone band may break if scratched.