DAIWA Kohga MX Air Portable N70XHB-Metal AP

Introducing a 2-piece high-sensitivity tie rubber rod with excellent portability.

The standard model is equipped with a high-sensitivity metal top and has good bite. The spinning model has a mega-top specification in consideration of the cast and realizes good bite. The TG model has achieved the ultimate bend that can only be achieved with a full solid thrill game. The blanks have power due to the effect of the optimum structure X45 against twisting, and by adopting a V joint even though it is 2 pieces, beautiful bending and power loss are reduced. You can enjoy interacting with the big die with confidence. In addition, an air sensor seat (slim trigger) is used for the reel seat to achieve both weight reduction and ease of grip. The degree of freedom of grip has also increased, enabling comfortable retrieval.

Kohga MX Air Portable N69HB-METAL AP

40g-100g optimally designed riding condition model that is easy to handle in all areas

Air sensor seat (slim trigger)

TECHNOLOGY :

■ Metal top (METAL model only)

Super elastic titanium alloy tip "Metal top". By using a very supple and sensitive metal for the tip, it is possible to clearly capture even the slightest bite of red sea bream rubber with "eye sensitivity" and "hand sensitivity".

■ Mega Top (C69MHS-S AP / TG model only)

It has high strength and rigidity due to the uniform dispersion of fiber and resin, and not only the sensitivity that resonates with the hand peculiar to carbon material, but also the eye sensitivity that appears at the tip of the ear is higher than before. Also greatly improved.

■ X45

The winding angles of X45 carbon fiber are 0 °, 45 °, and 90 ° with respect to the rod tip, respectively, which have the maximum elasticity against bending, swaying, and twisting. If this is set to an intermediate angle, the elasticity of each is low, which causes power loss. In addition, a considerable weight increase is required to exert the same power as the "X45" at an intermediate angle. The "X45", which uses the three angles with the highest elastic modulus, is the optimum structure that prevents deformation of the rod and improves power, operability, and sensitivity.

■ V-JOINT [V-joint]

Smooth knot bending realizes ideal tone and power-up. DAIWA's original bias structure is used for the joints. Achieves smooth bending of the mating part and improves power response and sensitivity.

■ HVF

In the carbon sheet that most affects the rod performance, Daiwa pays attention not only to the high elasticity of the carbon fiber itself, but also to the amount of adhesive resin that holds the carbon fiber together. "High-density HVF carbon", which reduces the amount of resin, which can be said to be extravagant, and instead increases the density of carbon fiber, is more muscular and powerful. It is the best material for rods that emphasize stickiness and strength.

*** ■ About the temperature change of the metal top.

Due to the characteristics of the material of superelastic titanium alloy, the elasticity of the superelastic titanium alloy decreases in a low temperature environment of 5 ° C or less, and the return of the tip of the tip becomes slow. Due to the extreme cold in the early morning and at night and the influence of the wind, a noticeable bend may occur. Furthermore, in an environment of 0 ° C or lower, the decrease in elasticity progresses further, causing a phenomenon in which the tips of the tips remain bent and do not return. In either case, if the temperature rises, it will return to its original superelasticity and can be used normally.

■ Please avoid using it that causes excessive bending.
The metal top can be used comfortably in normal operation, but excessive bending due to external factors such as entanglement and thread entanglement at the tip may leave habit (plastic deformation) or damage due to metal fatigue.

■ You can correct any habits by hand.
If a habit remains as in 2, you can correct it by slowly bending it in the direction opposite to the curved side. However, repeated correction of habits may cause metal fatigue, so avoid operations that leave habits such as entanglement.

Please be sure to read the instruction manual for comfortable use.