ABU GARCIA Zenon LTX
Обзор
A lightweight 150g bait finesse model. Equipped with a low inertia lightweight 30mm diameter spool, it achieves high castability in the spinning range. FW/SW compatible.
Rugged durametal frame, ceramic super free spool bearing, 30mm diameter 8lb-50m spool, MAGTRAX III brake, high gear 8.3:1, 85mm Dura carbon handle, hollow handle knob, etc., it is a specification that supports FW/SW bait finesse.
Ergonomic Design
ZENON's reel body is designed with an ergonomic design. In general bait casting reels, it was common sense to make the rear end positions of the left and right side plates the same. In ZENON, only the rear end of the palming side plate is moved forward. The clutch bar is designed asymmetrically to prevent accidental "pushing" due to palm interference when palming. As a result, palming and clutch operability have been dramatically improved.
Pinion support structure
The powerful winding of the handle is transmitted in the order of drive gear → pinion gear → spool. Even slight distortion in each part in this rotation transmission will have a negative effect on the rotation. The pinion support structure reliably supports the outer part of the pinion gear with the crank side plate via a ball bearing. This structure achieves highly efficient winding and a significant improvement in gear feel. Furthermore, when casting, optimal spool free and castability are achieved by maintaining a constant appropriate clearance between the inner surface of the pinion gear and the rotating spool shaft.
Large diameter drive gear
The ZENON series is not just about making it smaller and lighter, but also focusing on improving the durability of the gear to make fishing more comfortable. The ZENON is equipped with a large diameter drive gear. The MG7 and LTX are made of lightweight, high-strength ultra-super duralumin. In addition, the synergistic effect with the pinion support structure has resulted in a highly efficient, light and comfortable winding and an approximately 20% increase in the durability of the gearing.
High-strength Durametal frame
The Durametal frame is made of aluminum alloy, providing optimal strength and durability. It is also made of a material that is designed for tough use in saltwater fishing.
C6 Carbon Side Plates
C6 Carbon material is an engineering plastic reinforced with Abu Garcia's proprietary carbon fiber, and its rigidity is comparable to that of magnesium. The use of this material has achieved significant weight reduction without sacrificing strength and durability.
Ultra-lightweight φ30mm bait finesse spool made of super duralumin
The newly designed 30mm diameter spool uses the latest analytical technology and super duralumin material to achieve a lightweight design without sacrificing strength. The simple MAGTRAX III brake system and ceramic super free spool BB work together to achieve a different level of performance in terms of low trajectory pitching of ultra-lightweight rigs, casting feel of medium-weight lures, and casting distance.
Carbon Matrix Drag & Drag Clicker
Abu Garcia's unique carbon matrix drag washer allows for higher drag force while maintaining smooth performance over a wide range. By introducing a clicker, you can hear the clicking sound to indicate the speed of the drag, allowing you to keep an eye on line breaks while you're fishing.
Salt shield ball bearing
By adopting a newly developed ball bearing with a water-repellent coating applied to the entire inside and outside, the salt jamming phenomenon that causes abnormal rotation noise has been greatly reduced.
We have succeeded in significantly improving the rotation feel and durability. It is adopted in the pinion gear part, which is the part of a double-axis reel where salt crystals are most likely to remain.
MAGTRAX III Brake
Abu Garcia's MAGTRAX III brake has a reliable and simple structure. The simple structure can reliably prevent backlash. You can also adjust the number of internal magnets to suit your casting skills. Its characteristic is that the brake works reliably from the moment the lure is released during casting, so backlash can be reliably prevented even when using lures with high air resistance in headwinds. It also makes it possible to aim at a pinpoint when pitching a lightweight rig or casting a short distance.
The MG7 and LTX models are set to 8 magnets by default.
85mm Crank Dura Carbon Handle & Star Drag
The handle arm is made of laminated highly elastic carbon material, which makes it strong, lightweight and improves sensitivity. The length is a crank type of 85mm, taking into consideration all-round use and retrieval with the wrist. The star wheel, like the handle arm, is also made of carbon, which greatly contributes to weight reduction.
Cam lock lever
The cam lock lever for opening the palm side plate is located at the bottom of the side plate. When the cam lock lever is in the "open" position, the claw of the lever protrudes, preventing you from forgetting to tighten the lever.
Recessed reel foot
Abu Garcia's recessed reel foot allows the spool to be placed as close to the bottom of the reel as possible, resulting in an optimal low profile.
Aluminum front plate
The machine-cut aluminum front plate has a compact shape that provides protection for the level wind and prevents line tangles. It also minimizes damage to the reel if it is accidentally dropped to the ground.
Характеристики
Reel Size | 0 |
Reel Gear Ratio | 8.3 |
Reel Weight | 150 г |
Reel Spool Depth | PE #1 - 100 m |
Reel Bearing # +1 | 9 |
Reel Drag Force | 5 кг |
Reel Winding Length | 78 cm |
Reel Other | Handle length: 85 mm |
Brand | ABU GARCIA |
Оставьте отзыв об этом товаре первым!